Cantilever Rack Arms Explained: Length, Capacity, and Spacing | Cantilever Rack Supply
Post 9 — Component Guide

Cantilever Rack Arms Explained: How to Choose Length, Capacity, and Spacing

The arm is the part of a cantilever rack that actually carries your material. Pick the wrong length, style, or spacing and you get sag, roll-out, or an arm working beyond its rating. Here is how to choose correctly.

LOAD DEPTHARM TIP STOPCOLUMN
Length follows load depth
Capacity is rated at a length
Spacing runs two ways
Different types of cantilever rack arms showing straight, inclined, tip-stop, and heavy-duty arm designs
The right cantilever rack arm design depends on material type, bundle depth, load weight, and storage requirements.
Anatomy

Anatomy of a Cantilever Arm

Four features decide how an arm performs.

Bearing surfaceTop face that supports the load: flat, inclined, wide, or padded.
TipOuter end. A lip or stop here is the main defence against sliding or rolling.
ConnectionBolted (structural) or clip-in (roll-formed) attachment to the column.
ProfileSteel section and thickness, which with length set the rated capacity.
Arm Types

Cantilever Arm Types and When to Use Each

Match the arm style to how your material behaves under load.

Straight (flat)

Level bearing surface with no raised tip.

Boards, tube, stable bundles

Inclined

Slopes upward toward the tip so loads settle back toward the column.

Round bar, pipe, tube

Tip-stop / lipped

Raised lip or removable stop at the tip.

Anything that could slide

Pin / separator

Pins or dividers split the arm into lanes.

Mixed diameters, grade separation

Wide-bearing

Broader flat surface, sometimes padded.

Plywood, panels, sheet goods

Heavy-duty structural

Hot-rolled structural section.

Steel, heavy pipe, shapes
Connections

Bolt-On vs. Clip-In Arms

The connection sets both your capacity ceiling and how easily you can reconfigure.

Structural systems

Bolt-on arms

Very strong and rated for heavy loads. Changing arm height means unloading the column and re-bolting. Ideal for heavy-duty structural cantilever applications.

Roll-formed systems

Clip-in arms

Lock into punched slots; heights change quickly without tools. Rated for lighter loads. Browse available cantilever rack systems.

Confirm every clip-in arm is fully seated and locked before loading, and use arms from the same manufacturer and system as the column. Mixed components have no certified rating.
Sizing

How to Choose Arm Length

Arm length follows the depth of your load, meaning the width of the bundle measured across the arm. It does not follow material length, which runs along the aisle and is carried by several arms.

1

Measure the widest bundle or stack you will place on one arm.

2

Choose the shortest standard arm that supports most of that depth. Many manufacturers use roughly two-thirds of load depth as a minimum; confirm the rule for your system.

3

Read the capacity at that exact length. Capacity drops as arms get longer, so an over-long arm wastes capacity and protrudes into the aisle. See our guide on correct arm length selection.

4

Check aisle clearance on double-sided rows with your forklift's requirements.

Capacity & Spacing

Choosing Capacity and Spacing

Arm capacity is a per-arm rating at a specific length, assuming a load spread along the arm. Size it to the heaviest load that will ever sit on one arm, plus a margin, and keep each column within its own rating. Tip-loaded weight is worse than the rating assumes, so ask for point-load data if it applies. Spacing is often confused because it runs in two directions:

Vertical spacing

Level to level. Set by the tallest load on each level plus enough clearance for the forklift to enter and leave without catching the arm above.

Horizontal spacing

Column spacing along the bay. This governs sag in long materials. Flexible materials like lumber and plastic pipe need closer supports than stiff steel; heavier bundles need closer supports than light ones. Get the maximum span from your supplier.

Quick Reference

Arm Selection by Material

MaterialArm styleKey checks
Dimensional lumberStraight or slightly inclined, wide bearingSupport spacing; drainage if outdoors
Plywood / sheet goodsWide-bearing, paddedEdge support; avoid point loads
Steel bar and rodInclined with tip stopPer-arm rating at length; roll-out
Pipe and tubeInclined or pin armsRoll-out; thin-wall pipe can deform
Structural shapesHeavy-duty straightCapacity at length; stable seating
Aluminum / stainlessPadded or coatedKeep away from carbon-steel contact
Avoid These

5 Common Arm Selection Mistakes

  1. Sizing arm length from material length instead of load depth.
  2. Reading the capacity rating at a different arm length than the one installed.
  3. Leaving off tip stops or inclined arms when storing round stock.
  4. Mixing arms and columns from different manufacturers.
  5. Keeping a bent or permanently deformed arm in service. Remove it and replace it with a manufacturer-certified part; never repair it in the field.
Common Questions

Frequently Asked Questions

What are the main types of cantilever rack arms?

Straight, inclined (raised tip), tip-stop or lipped, pin or separator, wide-bearing for sheet goods, and heavy-duty structural arms. The right one depends on the material and how likely it is to roll or slide.

Are adjustable cantilever arms safe?

Yes, when fully seated and used within their rating. Clip-in arms allow quick height changes but carry lighter loads than bolted structural arms.

How long should a cantilever arm be?

Long enough to support most of the depth of your widest bundle, and no longer. Check the rated capacity at that length. Request a free quote with your bundle dimensions for a recommended arm length.

Does arm capacity change with length?

Yes. For the same profile, longer arms carry less. Always use the rating at the exact length installed. Learn more in our arm length guide.

Can I mix arms from different manufacturers?

No. Connection profiles and ratings differ, and a mixed system has no certified capacity.

When should an arm be replaced?

When it is bent, cracked, permanently deflected, or loose at the connection. Replace it with a manufacturer-certified part. See our guide on cantilever beam deflection for deflection limits.

Specify It Right

Need Help Choosing Arms?

Send us your material, bundle size, and weight. We will recommend arm type, length, and capacity and include a free layout review.