Cantilever Rack Arms Explained: How to Choose Length, Capacity, and Spacing
The arm is the part of a cantilever rack that actually carries your material. Pick the wrong length, style, or spacing and you get sag, roll-out, or an arm working beyond its rating. Here is how to choose correctly.
Anatomy of a Cantilever Arm
Four features decide how an arm performs.
Cantilever Arm Types and When to Use Each
Match the arm style to how your material behaves under load.
Straight (flat)
Level bearing surface with no raised tip.
Boards, tube, stable bundlesInclined
Slopes upward toward the tip so loads settle back toward the column.
Round bar, pipe, tubeTip-stop / lipped
Raised lip or removable stop at the tip.
Anything that could slidePin / separator
Pins or dividers split the arm into lanes.
Mixed diameters, grade separationWide-bearing
Broader flat surface, sometimes padded.
Plywood, panels, sheet goodsHeavy-duty structural
Hot-rolled structural section.
Steel, heavy pipe, shapesBolt-On vs. Clip-In Arms
The connection sets both your capacity ceiling and how easily you can reconfigure.
Bolt-on arms
Very strong and rated for heavy loads. Changing arm height means unloading the column and re-bolting. Ideal for heavy-duty structural cantilever applications.
Clip-in arms
Lock into punched slots; heights change quickly without tools. Rated for lighter loads. Browse available cantilever rack systems.
How to Choose Arm Length
Arm length follows the depth of your load, meaning the width of the bundle measured across the arm. It does not follow material length, which runs along the aisle and is carried by several arms.
Measure the widest bundle or stack you will place on one arm.
Choose the shortest standard arm that supports most of that depth. Many manufacturers use roughly two-thirds of load depth as a minimum; confirm the rule for your system.
Read the capacity at that exact length. Capacity drops as arms get longer, so an over-long arm wastes capacity and protrudes into the aisle. See our guide on correct arm length selection.
Check aisle clearance on double-sided rows with your forklift's requirements.
Choosing Capacity and Spacing
Arm capacity is a per-arm rating at a specific length, assuming a load spread along the arm. Size it to the heaviest load that will ever sit on one arm, plus a margin, and keep each column within its own rating. Tip-loaded weight is worse than the rating assumes, so ask for point-load data if it applies. Spacing is often confused because it runs in two directions:
Vertical spacing
Level to level. Set by the tallest load on each level plus enough clearance for the forklift to enter and leave without catching the arm above.
Horizontal spacing
Column spacing along the bay. This governs sag in long materials. Flexible materials like lumber and plastic pipe need closer supports than stiff steel; heavier bundles need closer supports than light ones. Get the maximum span from your supplier.
Arm Selection by Material
| Material | Arm style | Key checks |
|---|---|---|
| Dimensional lumber | Straight or slightly inclined, wide bearing | Support spacing; drainage if outdoors |
| Plywood / sheet goods | Wide-bearing, padded | Edge support; avoid point loads |
| Steel bar and rod | Inclined with tip stop | Per-arm rating at length; roll-out |
| Pipe and tube | Inclined or pin arms | Roll-out; thin-wall pipe can deform |
| Structural shapes | Heavy-duty straight | Capacity at length; stable seating |
| Aluminum / stainless | Padded or coated | Keep away from carbon-steel contact |
5 Common Arm Selection Mistakes
- Sizing arm length from material length instead of load depth.
- Reading the capacity rating at a different arm length than the one installed.
- Leaving off tip stops or inclined arms when storing round stock.
- Mixing arms and columns from different manufacturers.
- Keeping a bent or permanently deformed arm in service. Remove it and replace it with a manufacturer-certified part; never repair it in the field.
Frequently Asked Questions
What are the main types of cantilever rack arms?
Straight, inclined (raised tip), tip-stop or lipped, pin or separator, wide-bearing for sheet goods, and heavy-duty structural arms. The right one depends on the material and how likely it is to roll or slide.
Are adjustable cantilever arms safe?
Yes, when fully seated and used within their rating. Clip-in arms allow quick height changes but carry lighter loads than bolted structural arms.
How long should a cantilever arm be?
Long enough to support most of the depth of your widest bundle, and no longer. Check the rated capacity at that length. Request a free quote with your bundle dimensions for a recommended arm length.
Does arm capacity change with length?
Yes. For the same profile, longer arms carry less. Always use the rating at the exact length installed. Learn more in our arm length guide.
Can I mix arms from different manufacturers?
No. Connection profiles and ratings differ, and a mixed system has no certified capacity.
When should an arm be replaced?
When it is bent, cracked, permanently deflected, or loose at the connection. Replace it with a manufacturer-certified part. See our guide on cantilever beam deflection for deflection limits.
Need Help Choosing Arms?
Send us your material, bundle size, and weight. We will recommend arm type, length, and capacity and include a free layout review.